Comark - DT400 - -4 - 400 F Digital Thermometer

SKU: 81197
Price: $22.94/EA
- Buy 5 or more $21.22/EA
Shipping Info: Stock item, same day shipping M-F
Bulk Discount Available


  • Waterproof pocket thermometer
  • Temperature range -4° to 400°F (-20° to 200°C)
  • Digital display
  • Accuracy ±1°F
  • Commercial dishwasher safe
  • Can be field calibrated
  • Max temperature hold feature helps determine max temperature of commercial dishwashers during wash cycle
  • Data hold feature
  • Auto power off helps save battery life
  • 5 in stem - thin tapered tip for a quick response
  • Response time under 6 seconds
  • BioCote® antimicrobial protection
  • NSF certified
  • 1 year warranty
  • Display: Digital
  • Stem Length: 5 in
  • High Temperature: 400°F
  • Low Temperature: -4°F

Do you have questions about this product?

get answers from real customers and in-house experts with AnswerBox.

3 Questions | 3 Answers
Displaying questions 1-3
  • Q:

    HOw do I get my Comark dt400 to read above 99degrees C?

    HOw do I get my Comark dt400 to read above 99degrees C?
    Asked on 4/4/2013 by Anonymous

    1 answer

    • A:

      Thanks for contacting Tundra Restaurant Supply with your question.

      A good way to test your Comark DT400 Waterproof Pocket Digital Thermometer to make sure it's reading temperature correctly is to use it in boiling water. Boil some water and stick the probe end of the thermometer in. If the temperature does not read above 99°C then there's a good chance the thermometer is malfunctioning and may need to be replaced.

      That said, if the readout is above 99°C it's possible that there may be an issue with your dishwasher water temperature.

      Answered on 4/4/2013 by Andrew Call from Boulder, CO
  • Q:

    how to get 32F stable reading while calibrating Comark DT400 Waterproof Digital Thermometer ?

    When i try to calibrate using ice water solution, the above mentioned thermometer most of the times don't show 32F, instead the stable reading range from 31.2- 31.8F when I press & hold D-H button for 8 secs. Am i missing some steps or doing it wrong?
    Asked on 4/21/2012 by sanny from san francisco

    1 answer

    • A:

      No you are doing the calibration correctly Thermometer has a Accuracy of ±1°F/0.5°C. Re-calibrate by merely submerging tip in proper ice water bath and holding down the button for 8 seconds.

      Answered on 4/22/2012 by Areomax from Far North BC Canada
  • Q:

    how to calibrate the dt 400
    Asked on 7/27/2011 by hammer from hampton va

    1 answer

    • A:

      Field Calibration Procedures:
      1. The DT400 is only calibratable in a slush ice solution (60% crushed Ice and 40% tap water) or a water bath. Do not attempt to calibrate in any other manor.
      2. Immerse the stem of the thermometer to at least half the length in the slush ice solution.
      3. Wait for the reading to become stable (usually ± 2º of 32ºF or ± 1º of 0ºC).
      4. Press and hold the D-H button for 8 seconds to begin calibration.
      5. CAL will be displayed for 2 seconds and the calibration at 32ºF/0ºC is completed.
      6. Remove the thermometer from the ice water and continue to take measurements.

      Answered on 8/1/2011 by Molly from Boulder, CO
Displaying questions 1-3

Do you have a question about this product?